-
Who this checklist is for
-
The 9-step sourcing checklist
-
Step 1: Lock the capacity number before you look at a single quote
-
Step 2: Find out whether you're talking to a manufacturer or a trader
-
Step 3: Get the quote broken into line items, not a headline number
-
Step 4: Verify certifications—don't just accept the PDF
-
Step 5: Spec the refrigeration system and cycle time in writing
-
Step 6: Get lead time in writing—with penalties
-
Step 7: Clarify installation and commissioning scope—and who pays for the engineer's flight
-
Step 8: Lock down parts and service before you sign
-
Step 9: Structure payment so your deposit is protected
-
Step 1: Lock the capacity number before you look at a single quote
-
Common mistakes and what to watch for
Who this checklist is for
If you're sourcing an industrial freeze dryer and the quotes you've collected are wildly different—say, $65,000 from one vendor and $180,000 from another for what the spec sheet claims is the same machine—this is for you. I work in equipment sourcing, and I've handled 60+ rush freeze dryer orders in four years, including same-day turnarounds for food and pharma clients. Here's the thing: most of those rush orders didn't start as emergencies. They started as a normal purchase that crept up on a deadline because someone skipped a step in the first week.
Below are the nine steps. None of them take longer than a week to complete. Done together, they'll save you the 30–40% premium I routinely see companies pay when they're forced into a panic buy. I'll cover what to check, what to ask, and what to walk away from.
The 9-step sourcing checklist
Step 1: Lock the capacity number before you look at a single quote
This is the step most buyers get wrong, and it's the one that causes the most expensive downstream problems. Freeze dryer capacity gets quoted in two different units—chamber volume (liters or cubic feet) and ice capacity (kg or lb of water per 24 hours)—and they aren't interchangeable. A 500-liter chamber might only pull 80 kg of ice per cycle if the refrigeration system is undersized.
When I compared two quotes for a food client side by side—same chamber volume, same ballpark price—I finally understood why the cheap one looked good on paper and bad in production. The cheap unit used a smaller compressor and a manual defrost; the client's actual throughput requirement was 30% higher than what that machine could cycle in a week.
Ask specifically: How many kilograms of wet product can this machine process per 24-hour cycle at my shelf loading? If the vendor answers in liters, ask again.
Step 2: Find out whether you're talking to a manufacturer or a trader
Not every company selling industrial freeze dryers builds them. Traders are legitimate businesses, but they typically add 15–30% margin on top of the factory price and are harder to hold accountable once the machine ships. Before you go further, verify which one you have.
- Ask for a live, timestamped video walkthrough of the production floor—not a stock factory tour video from 2019.
- Check the business license scope (in China, this is the "经营范围" field; in the EU, the company register at the chamber of commerce).
- If the order is above $100k, budget for a factory visit. Yes, it's a trip. It's still cheaper than a rework.
If you can't visit, at minimum ask for the names of two customers in your region who bought the same model in the last 24 months. Then actually call one of them.
Step 3: Get the quote broken into line items, not a headline number
"$95,000 for the freeze dryer" tells you almost nothing. Two quotes at the same headline price can differ by 40% in delivered cost once you account for refrigeration, vacuum pump, controls, freight, installation, and training. Ask for a line-item breakdown covering:
- Unit base price
- Refrigeration system (compressor brand, refrigerant type)
- Vacuum pump (model and brand)
- Control system and data logging
- Shipping terms (FOB, CIF, DDP—they are not the same number)
- Installation and commissioning labor
- Operator training
- Warranty period and what it excludes
If a vendor won't break it out, that's data. It usually means the line items are padded somewhere.
Step 4: Verify certifications—don't just accept the PDF
Which certification you need depends on where the machine is installed and what it processes. For most industrial freeze dryers, the ones that actually matter are:
- CE marking (EU machinery directive) if the unit enters the EU/EEA
- ASME Section VIII or PED 2014/68/EU for the pressure chambers—freeze dryers are vacuum vessels, and this is where certification genuinely affects safety
- UL or ETL for US electrical components
- ISO 9001 for the factory's quality management (nice to have, not a substitute for product certification)
I knew I should've called the issuing body to confirm the certificate number on one quote—but I thought, "What are the odds?" That was the one time it mattered. The certificate was for a different model, and the client found out during installation, eight weeks later. Not a cheap conversation.
Ask for certificate numbers, then verify them with the issuing body directly. It takes an email and a day.
Step 5: Spec the refrigeration system and cycle time in writing
This is where the "cheap" unit bites in year two. Cycle time in a freeze dryer breaks into three phases: freeze, primary dry, secondary dry. Ask the vendor to state the expected duration of each phase for your product, and to warrant the total cycle time in the contract. If they only warrant chamber volume and pull-down temperature, you're buying a box, not a process.
Also ask: what refrigerant does the system use? R-404A and R-508B are common; some regions are phasing down high-GWP refrigerants, and you don't want to discover a service problem five years out because the refrigerant is restricted where the machine is installed.
Step 6: Get lead time in writing—with penalties
"About 90 days" is not a lead time. A lead time is: X days from receipt of deposit and approval of final drawings, with a stated penalty for late delivery (typically 0.5–1% of the PO value per week, capped at 5–10%). Ask specifically what triggers the clock and what freezes it. Delays from "client approval pending" are the vendor's favorite excuse—so put a hard cap on how long they can wait for your sign-off before it becomes their problem again.
Step 7: Clarify installation and commissioning scope—and who pays for the engineer's flight
This is the line item where "included" turns out to mean "we'll send you a manual." Confirm:
- How many days of on-site commissioning are included?
- Who covers the engineer's flights, hotel, per diem, and visa?
- What is the sign-off criterion for the performance test—specific temperatures, vacuum levels, and cycle times?
- What happens if the machine fails commissioning?
Get the performance test criteria written into the PO. "Site acceptance test" without numbers is a phrase, not a test.
Step 8: Lock down parts and service before you sign
What happens when the compressor fails in year three? Ask for a recommended spare parts list with current lead times and unit prices. Then ask where the nearest service agent is. If the answer is "we can send an engineer from our factory," get the estimated mobilization time—it might be 10 days, and 10 days of downtime in a pharma line is a much bigger number than the service call.
Step 9: Structure payment so your deposit is protected
Never accept 100% T/T upfront—no legitimate manufacturer requires it, regardless of what the salesperson says. Standard structures are 30% deposit / 70% before shipment, or irrevocable L/C at sight. For orders above $200k, ask about a performance bond or escrow through a bank both sides trust. Part of me finds the escrow fees annoying (they can run 0.5–1%), but another part has seen what happens when the deposit goes missing—and the fees are a rounding error compared to that.
Common mistakes and what to watch for
Mistake #1: Comparing quotes by headline price. Compare delivered, installed, commissioned cost—including the performance test. That's the only number that matters.
Mistake #2: Skipping the reference call. Every vendor will give you references. Call them. Ask what broke in year one. Ask how quickly it was fixed.
Mistake #3: Treating rush fees as normal. They aren't. A 2023 purchase by a food client I worked with was expedited for $18,000 in air freight—because the deposit was sent three weeks late. The $18,000 was the cost of an internal sign-off nobody chased.
There's something satisfying about a sourcing process that finishes on schedule with no drama. After a few rush jobs where the answer to "can we make it?" was "unfortunately, not anymore," I've come around to the boring version. Five minutes of verification beats five days of correction—and in this category, five days of correction usually costs a lot more than a freight bill.